FRAM Fresh Breeze® Cabin Air Filter
| Height (Inch) | 0.985 |
|---|---|
| Width (Inch) | 7.053 |
| Length (Inch) | 8.116 |
Search
- Description
FRAM® Fresh Breeze cabin air filters can keep up to 98% of road dust and pollen particles from entering a vehicle. The only cabin air filter that uses the natural deodorizing properties of ARM & HAMMER™ baking soda. Contaminants that enter the vehicle with outside air through the vehicle’s air conditioning, heating and ventilation system can become concentrated and expose passengers to road dust, dirt and allergens at higher levels than outside the car.
- Filters up to 98% of dust, pollen and other contaminants
- ARM & HAMMER baking soda combined with carbon embedded in the filter assists in cleaning outside air flowing through the vehicle’s ventilation system
- Helps protect your vehicle's heating and air conditioning unit while also keeping it working efficiently
- Installs on average in 15 minutes
1. Road dust and pollen particles ranging in size from 5-100 microns.
2. Deodorizing tests used isovaleric acid (sweaty odors), geosmin (earthy odors) and dog hairs.
3. ARM & HAMMER, the ARM & HAMMER logo and distinct orange trade dress are trademarks of Church & Dwight Co., Inc. and used under license by FRAM Group IP LLC.
* Always follow OE recommended change intervals.
- Applications
This Item Fits the Following Vehicles:
Year Make Model Engine 14-11 FORD MUSTANG V6-3.7L 10-05 FORD MUSTANG V6-4.0L 10-05 FORD MUSTANG V8-4.6L 14-11 FORD MUSTANG V8-5.0L 12-07 FORD MUSTANG V8-5.4L 14-13 FORD MUSTANG V8-5.8L - Comparison
COMPETITOR NAME COMPETITOR PART # ATP CF-19 ATP CF-282 Bosch P3756WS Carquest 89687 Champ CAF1807C Champion CCF1807 Driveworks DW-25572 Ford 4R3Z-19N619-AA FVP F4687C FVP F4687 Hastings AFC1312 Hastings AF1312 K&N VF2020 Kleener CAF1807P Kleener FCAF1807P Kleener CAF1807C Kleener FCAF1807C LUBER-FINER CAF1807P LUBER-FINER CAF1807C MAHLE LA1062 MicroGard 3969 MicroGard 4098 Micronair FD05151 Motorcraft FP-53 Motorcraft FP-72 NAPA 4687 NAPA ProSelect Filters 2230105 Parts Master 94687 Performax PC-77 Power Train 3969 Premium Guard PC5572 Promotive C25572P Pronto PC-5572 PUREPRO C25572 Purolator C25572 Service Champ C25572 STP CAF1807C STP CAF1807P SUPERTECH 5275 Valvoline VCA-1102 VIPER 10370C Wix 24687 Wix WP10105 - Installation
TOOLS: Phillips-head Screwdriver.
LOCATION OF CABIN FILTER: In front of the windshield on the passenger side of the vehicle under the cowl vent screen.
REMOVE ALL DEBRIS IN AND AROUND FILTER LOCATION.
- Open the hood.
- Using the Phillips-head screwdriver remove the two plastic screws securing the front of the cowl vent screen on the passenger side of the vehicle. It may be necessary to hold the bottom of the clips that the screws are in to keep the clips from turning with the screw.
- After removing the screws squeeze in on the plastic clips and pull them out of the hole in the cowling.
- Gently lift up the front edge of the passenger side cowl vent screen. It is not necessary to remove the cowl vent screen.
- You should now see the filter toward the passenger side. Press down on the frame and pull forward so that it slips under the tab. If you don’t the frame won’t come out. Grasp the plastic frame that the filter is in by the top tab and pull towards the front of the vehicle and remove it.
- . Remove the dirty filter from the frame and replace with the clean filter.When putting the clean filter in the frame make sure the air flow arrow printed on the filter is pointing up and that the arrow will be facing the rear of the vehicle when you reinstall the frame back in the vehicle. Also insure that the filter is installed in the frame with the flaps folded back on the filter and the folded edge inserted into the frame first. Also the last pleats of the new filter need to be over the slots in the filter frame.
- You will need to again gently lift up on the front edge of the passenger side cowl and reinstall the frame into the housing on the vehicle and snap it back into place.
- Reposition the cowl and align the holes in the front of the cowl and push the clips back in the holes. Use the Phillips-head screwdriver and reinstall the plastic screws back into the clips and secure them.
- Close the hood.