FRAM Fresh Breeze® Cabin Air Filter
| Height (Inch) | 1.655 |
|---|---|
| Width (Inch) | 3.073 |
| Length (Inch) | 18.439 |
Search
- Description
FRAM® Fresh Breeze cabin air filters can keep up to 98% of road dust and pollen particles from entering a vehicle. The only cabin air filter that uses the natural deodorizing properties of ARM & HAMMER™ baking soda. Contaminants that enter the vehicle with outside air through the vehicle’s air conditioning, heating and ventilation system can become concentrated and expose passengers to road dust, dirt and allergens at higher levels than outside the car.
- Filters up to 98% of dust, pollen and other contaminants
- ARM & HAMMER baking soda combined with carbon embedded in the filter assists in cleaning outside air flowing through the vehicle’s ventilation system
- Helps protect your vehicle's heating and air conditioning unit while also keeping it working efficiently
- Installs on average in 15 minutes
1. Road dust and pollen particles ranging in size from 5-100 microns.
2. Deodorizing tests used isovaleric acid (sweaty odors), geosmin (earthy odors) and dog hairs.
3. ARM & HAMMER, the ARM & HAMMER logo and distinct orange trade dress are trademarks of Church & Dwight Co., Inc. and used under license by FRAM Group IP LLC.
* Always follow OE recommended change intervals.
- Applications
This Item Fits the Following Vehicles:
Year Make Model Engine 04-99 JEEP GRAND CHEROKEE L6-4.0L 09-07 JEEP GRAND CHEROKEE V6-3.0L 10-05 JEEP GRAND CHEROKEE V6-3.7L 09-99 JEEP GRAND CHEROKEE V8-4.7L 10-05 JEEP GRAND CHEROKEE V8-5.7L 10-06 JEEP GRAND CHEROKEE V8-6.1L - Comparison
COMPETITOR NAME COMPETITOR PART # Baldwin PA4168 Bosch P3704WS Chrysler 82204691 Chrysler 82208300 Chrysler 5013595AB FVP F4903 Hastings AF1229 Hastings AFC1229 Kleener CAF1806P Kleener FCAF1806P LUBER-FINER CAF1806P LUBER-FINER CAF1806C MAHLE LA779 MicroGard 3062 Micronair CY01999 NAPA 4903 Power Train 3062 Premium Guard PC5599 Pronto PC-5599 Purolator C15599 STP CAF1806P Valvoline VCA-1170 Wix 24903 - Installation
TOOLS: T-30 Torx Wrench Standard Screwdriver.
LOCATION OF CABIN FILTER: In front of the windshield under the cowl vent screen on the passenger side of the vehicle.
REMOVE ALL DEBRIS IN AND AROUND FILTER LOCATION.
PLEASE NOTE: **No vehicles came standard with a cabin filter so if you want to install a cabin filter in your vehicle you will first need to buy a cabin filter housing from a Jeep Dealer. The housing is part # 822083000.
- With hood closed remove the three (3) plastic fasteners securing the cowl vent screen. To ease with removal of the fasteners gently lift on the end of the cowl vent screen to help get the fasteners started or use a flat blade screwdriver to gently pry up on the fastener while unscrewing them with the T-30 Torx wrench.
- Open the hood
- Grasp the cowl weather-strip on the passenger side and pull it outward to remove.
- Gently lift the cowl vent screen enough to locate the plastic air inlet cover or filter housing depending on if this is initial installation.
If initial installation follow the steps below. (**For first time installation a filter housing is required.) If this is not the initial installation and a filter is already present skip these steps and continue with step “6”.Locate the plastic tabs that secure the air inlet cover in place. Pull the thin side of the cover out first which is secured by one clip then rock the cover back and forth to remove the “rosebud” clip securing the center of the cover. Remove the cover and disregard or keep so you could install later if desired. The cover will not be needed once new housing and filter is installed. - Take the filter housing you bought from the dealer and insert it into the inlet opening and secure in place with the seal side down. With the housing in hand with seal side down. The housing will have a tab on the left hand end of the housing. This should slide under the far left hand side of the air inlet opening under the cowl vent screen. Once this is in place properly the two center holes in the housing should line up with the two holes present on the center of the air intake under the cowl vent screen. Take the two push type fasteners that came with your housing kit and push them securely into these center holes.
- Install the filter into the housing. The filter can only be installed one way.
- Re-seat the cowl vent screen in place.
- Re-install the cowl weather-strip.
- Close the hood and secure with the cowl vent screen fasteners using the T-30 Torx wrench. (Make sure fasteners are securely in place. If needed bend the locking tabs out on the fasteners to help them stay in place.)