FRAM Fresh Breeze® Cabin Air Filter
| Height (Inch) | 0.788 |
|---|---|
| Width (Inch) | 8.471 |
| Length (Inch) | 10.717 |
Search
- Description
FRAM® Fresh Breeze cabin air filters can keep up to 98% of road dust and pollen particles from entering a vehicle. The only cabin air filter that uses the natural deodorizing properties of ARM & HAMMER™ baking soda. Contaminants that enter the vehicle with outside air through the vehicle’s air conditioning, heating and ventilation system can become concentrated and expose passengers to road dust, dirt and allergens at higher levels than outside the car.
- Filters up to 98% of dust, pollen and other contaminants
- ARM & HAMMER baking soda combined with carbon embedded in the filter assists in cleaning outside air flowing through the vehicle’s ventilation system
- Helps protect your vehicle's heating and air conditioning unit while also keeping it working efficiently
- Installs on average in 15 minutes
1. Road dust and pollen particles ranging in size from 5-100 microns.
2. Deodorizing tests used isovaleric acid (sweaty odors), geosmin (earthy odors) and dog hairs.
3. ARM & HAMMER, the ARM & HAMMER logo and distinct orange trade dress are trademarks of Church & Dwight Co., Inc. and used under license by FRAM Group IP LLC.
* Always follow OE recommended change intervals.
- Applications
This Item Fits the Following Vehicles:
Year Make Model Engine 05-01 LEXUS IS300 L6-3.0L 03-99 LEXUS RX300 V6-3.0L 07-01 TOYOTA HIGHLANDER L4-2.4L 03-01 TOYOTA HIGHLANDER V6-3.0L 07-04 TOYOTA HIGHLANDER V6-3.3L - Comparison
COMPETITOR NAME COMPETITOR PART # ATP CF-48 Beck/Arnley 042-2027 Blue Print ADT32502 Bosch P3755WS Carquest 89901 Champ CAF1774 Champion CCF7774 Corteco 80000162 Defense Filters DC062 Driveworks DW-38222 FVP F4901 GK Industries CF1051 Group 7 C38222P Hastings AFC1245 Hastings AF1245 K&N VF2008 Kleener CAF1774 Kleener FCAF1774 Lexus 87139-YZZ04 Lexus 87139-48020 LUBER-FINER CAF7774 LUBER-FINER CAF1774 MAHLE LA199 MicroGard 3964 Micronair TY98163 NAPA 4901 Nipparts J1342004 Parts Master 94901 Performax PC-62 Power Train 3964 Premium Guard PC8222 Promotive C38222P Pronto PC-8222 PUREPRO C38222 Purolator C38222 Service Champ C38222 Service Pro MC38222 STP CAF1774 SUPERTECH 7275 Toyota 87139-48020 Toyota 87139-48020-83 Valeo 715542 VIPER 10138C Wix 24901 - Installation
TOOLS: Phillips-head Screwdriver
LOCATION OF CABIN FILTER: On the passenger side of the vehicle behind the glove compartment behind the cabin filter access panel.
REMOVE ALL DEBRIS IN AND AROUND FILTER LOCATION.
- While sitting in the passenger seat open the glove box. If the vehicle is equipped with a cabin filter there should be a label on the inside bottom panel of the glove box stating: “The air conditioning system has an air filter to eliminate dust pollen etc.” (If you are uncertain if the vehicle has a cabin filter or you would like to add a cabin filter you can continue with the procedure if the housing is present. Note: The glove box must be closed again to proceed.
- Unscrew the clip that secures the glove box dampener cable to the frame. This clip is located on the right side of the dash assembly below the glove box. The base of the clip will pull out of the hole in the frame if the screw is unscrewed to about half an inch. The cable will stay connected to the clip base.Note: The clip base will tend to spin in place so you may need to hold it from behind while turning the screw.
- Press inward on the sides of the glove box to disengage the stops. This will allow it to hang low enough to access the filter housing cover.
- Pull the filter housing door off of the housing to access the filter.
- Pull the filter frame straight out from the housing.
- Remove the old filter from the frame.
- Insert the new filter into the frame (flat side down). Be sure the filter is tucked under all retainer spurs along the edges.
- Slide the frame back into the housing.
- Snap the cover back into place. The cover has an “up” arrow to indicate the proper orientation.
- Close the glove box while pressing inward on the sides to re-engage the stops.
- Re-insert the dampener cable clip base into the frame. Press the screw firmly into place to lock.